SKU:
GLENF1BBRZ

GLENF1 - FHC Glendale Series Wall Mount Hinge - Full Back Plate - Compare to GEN037, HGTWFP

Brand :

(No reviews yet) Write a Review
$80.39
Edge Style:
Square
Compare to:
GEN037, HGTWFP
 
  • Compare to Geneva GEN037, Designer HGTWFP
  • Square Profile Glass to Wall Hinge with Full Back Plate
  • Designed For 3/8"-1/2" (10 mm to 12 mm) Tempered Glass
  • Many Popular Finishes to Select From
  • Self-Centering within 15 Degrees of Closing Position
  • Commonly used in Residential Bath and Commercial Hotel Applications
  • Reversible 5 Deg Pivot Pin For Jobs Requiring a Positive Closing Position
  • Replacement Screws PS102 and PS103 are Available as Needed
  • Can be used with Hinge Limit Plates HLP25 and HLP40

Glass Specifications

MAXIMUM DOOR CAPACITY 3/8" (10 mm) GLASS
Approx. 5 lb./ft²
1/2" (12 mm) GLASS
Approx. 6.4 lb./ft²
DOOR WEIGHT DOOR WIDTH
Using 2 Hinges 80 LBS (36 kg) 28" (711 mm)
Using 3 Hinges 120 LBS. (54 kg) 32" (813 mm)

NOTE: Do Not Exceed either maximum weight or width when choosing proper quantity of hinges.

 

Gasket Specifications

For 3/8" (10 mm) Glass: Use One Thick Gasket On Each Side For 1/2" (12 mm) Glass: Use One Thin Gasket On Each Side

Glass Instructions

Only use tempered safety glass. To prevent damage to the hinge finish during installation, do not use power tools when installing these hinges.

Overview

The Glendale Series Hinge has a dual degree pivot pin. It comes factory set at 90 degrees for normal door closing applications. There is also a secondary setting on the hinge pivot pin that can be field adjusted to allow an additional 5 degrees of closing for jobs that require a firmer positive position against a jamb or seal.

Care & Cleaning Guidelines

For best results, keep the following recommendations in mind when caring for your FHC shower door hardware. Your shower door should be dried daily with a soft towel or cloth to ensure its original finish. Do not use harsh cleaners or chemicals on the hardware, as many of the components are coated with a clear lacquer that will become damaged beyond repair. Always test your cleaning solution in an inconspicuous area prior to cleaning the entire hardware surface. Wipe surfaces clean using a soft, dampened cloth or sponge, and rinse completely with warm water immediately after applying the cleaning solution. Use only small amounts of liquid, gentle, cleaner. Never use abrasive products, sponges, or wire scrub brushes while cleaning hardware.

Maintenance

FHC's hinges come factory greased for a silent, hassle-free experience. If there is any noticeable squeaking that occurs after installation it is recommended to apply a few drops of (3 in 1) multi-purpose oil to the hinge, at the nylon washer/pivot location. The lubricant will penetrate the hinge crevices, reducing friction, cleaning grime, and/or buildup. Spray lubricants are prohibited. If, for some reason, the hinge is disassembled during maintenance, use a small amount of white lithium grease to lubricate the interior hinge components.

Material/Construction

Solid Brass with HD S/S Back Plate

 WARNING: This Product May Contain Chemicals Known to the State of California to Cause Cancer or Reproductive Harm. To Learn More Visit P65Warnings.ca.gov

 

More Information
Product Name FHC Glendale Series Wall Mount Hinge - Full Back Plate
Item No GLENF1
Compare To GEN037, HGTWFP
Air Freight Ships Air ,
Glass Fabrication Use FHC Template SD1 For Glass Fab Template
Minimum Order 1 Each
Product Height 3-1/2"
Product Weight 2 lb
Product Width 2-3/16"
Ship Via Ships UPS
Warnings Not for use with laminated glass
Warranty 3-Year Warranty

Downloadable Documents

 

 

Edge Style:
Square
Compare to:
GEN037, HGTWFP